An April map from a partly stocked contract warehouse does not establish July and August coverage on its own. Before assigning July and August inventory, check whether the study and supporting records cover peak outdoor heat, higher pallet loads and actual dock activity at the intended storage positions. If heat, cold or changed airflow could affect those positions and the evidence leaves that exposure unresolved, plan follow-up mapping under the missing conditions. A single campaign can be defensible for an isolated, fully conditioned area when supporting records show that it represents the intended load and relevant operating extremes, subject to the requirements that apply to the site. EU GDP § 3.2.1, MHRA Inspectorate commentary
Temperature mapping records how conditions vary across a defined area and identifies hot and cold locations. Routine monitoring tracks conditions over time at selected points, using the map to decide which positions matter. A stable reading at a thermostat in April establishes conditions at that point. Coverage of upper racks near the roof or staging space near an active dock needs evidence from locations that represent those exposures. WHO temperature-mapping supplement, MHRA Inspectorate commentary
Which source governs the warehouse decision?
| Source and scope | What it calls for | What it means for the seasonal decision |
|---|---|---|
| 21 CFR 211.142 · US finished-drug CGMP | Written warehousing procedures that include quarantine before quality-control release and appropriate storage conditions. | Use the rule to establish the storage obligation. The section specifies no mapping method, calendar, logger count, study duration or repeat interval. |
| EU GDP § 3.2.1 · Storage areas | Initial mapping before use under representative conditions, with routine monitoring devices located from the mapped extremes of fluctuation. | Repeat mapping according to risk assessment findings or when significant premises or temperature-control equipment modifications are made. |
| EU GDP § 9.4 · Temperature-controlled vehicles | Representative vehicle mapping that accounts for seasonal variation. | Apply the explicit seasonal language to vehicle mapping. Assess warehouse representativeness under § 3.2.1. |
| MHRA Inspectorate · UK inspection commentary | Repeat mapping to cover seasonal changes or reconfiguration, and justify future frequency in a documented risk assessment. | Check whether the initial load and weather captured the conditions that could move hot or cold locations. |
| WHO Supplement 8 · Technical guidance | A method for planning, carrying out and interpreting a storage-area mapping exercise. | Use the method to resolve gaps in spatial or seasonal evidence. The supplement discusses warm- and cold-season studies where storage areas are seasonally affected. |
US warehousing procedures under 21 CFR 211.142
Under US current good manufacturing practice (CGMP) for finished pharmaceuticals, § 211.142 requires written warehousing procedures to be established and followed. Paragraph (a) addresses quarantine before release by the quality control unit. Paragraph (b) requires storage “under appropriate conditions of temperature, humidity, and light so that the identity, strength, quality, and purity of the drug products are not affected.” Mapping can help a quality team demonstrate the temperature portion of that obligation. The paragraph leaves the choice of evidence and any seasonal mapping schedule unspecified. A temperature study also leaves humidity and light to be addressed where relevant. 21 CFR 211.142
EU GDP for storage areas and vehicles
The European Commission’s Good Distribution Practice guidelines cover wholesale distribution of medicinal products for human use, including manufacturers distributing their own products. Section 3.2.1 calls for an initial storage-area map before use under representative conditions and placement of permanent monitoring equipment based on the results. It calls for repetition according to risk assessment findings or whenever significant modifications are made to the facility or temperature-controlling equipment. For very small room-temperature premises, it directs operators to assess risks such as nearby heaters and place monitors accordingly. That provision addresses premises of only a few square meters. EU GDP introduction and § 3.2.1
Section 9.4 expressly names seasonal variation for temperature-controlled vehicles. For premises, § 3.2.1 instead leaves the site to establish which operating conditions its warehouse study represents. A summer dock plan, for example, can change both the extent of exposure to outside air and where products wait. The warehouse rationale should account for those conditions even if a separate vehicle study already covers the route. EU GDP §§ 3.2.1 and 9.4
UK inspection commentary and WHO’s mapping method
The MHRA Inspectorate’s 2016 commentary describes how inspectors expect warehouse teams to use the data. It calls for a repeat under fully stocked conditions when the initial study was run empty, and says dummy stock can simulate normal operations in smaller spaces. It also calls for mapping that covers seasonal variation and for a documented risk assessment to justify future frequency. In a reply posted under the article, Mark Birse points to winter heaters, skylights and the position of the sun as reasons the warmest and coldest locations can change through the year. Use the Inspectorate’s blog as an account of UK inspection expectations and base the site decision on the applicable GDP guidance and documented evidence. MHRA Inspectorate commentary
WHO’s Supplement 8 defines mapping as documented measurement of how temperature, relative humidity or both vary across the storage area, including the location of hot and cold spots. The technical method connects an approved study protocol, measurements, interpretation and actions. For seasonally affected spaces, the supplement describes warm- and cold-period studies as a way to observe the effect of weather and advises separating seasonal effects from other changes between campaigns. The supplement adds that two-season mapping is typically not necessary for cold rooms and freezer rooms. The relevant evidence for an individual room still depends on its enclosure, interfaces and operation. WHO Supplement 8 glossary and §§ 2.2–2.4
A worksheet for deciding whether to remap
Define the proposed use before comparing it with the original study. Specify the products’ applicable storage limits, the zones and rack heights they will occupy, expected load patterns and any locations where goods wait. Delineate the area that QA is being asked to approve. Then assemble the previous protocol, position plan, logger traces and report alongside records describing weather, building and operating conditions during the study. Use the following worksheet to identify which changes could affect stored product and which evidence would resolve each question. It applies the source principles to a site decision. EU GDP § 3.2.1, MHRA Inspectorate commentary, WHO temperature-mapping supplement
| Exposure to review | Evidence to compare with the original map | Decision if coverage is incomplete |
|---|---|---|
| Roof, exterior walls and skylights | Compare the affected rack faces, upper storage levels and perimeter positions with interior positions under plausible local heat or cold. Check how solar exposure changes across the proposed storage period. | Map the exposed positions during the missing thermal conditions if their response remains uncertain. |
| Dock doors and staging | Compare actual receiving and dispatch patterns, the length and timing of door openings, and how long goods wait in the relevant area. Match the events to the logger traces. | Capture representative dock operations where goods could be exposed. Define which staging positions the resulting evidence covers. |
| Building envelope and local climate | Check whether insulation, internal separation and adjoining spaces shield the occupied area from outside conditions. Compare dates and outdoor conditions for which there are usable indoor records. | Collect targeted evidence where exposure is uncertain. Use a seasonal campaign if the affected area has a material weather dependence. |
| Heating, ventilation and air conditioning (HVAC) | Compare system operating modes, setpoints, temperature-control schedules, and supply and return paths. Identify whether the first campaign exercised the modes relevant to the planned use. | Capture the missing operating mode or investigate the control change before relying on existing probe locations. |
| Load and rack layout | Compare pallet spacing, occupied heights, obstructions and air passages with the planned layout. Identify occupied levels and aisles the initial map sampled sparsely. | Map representative loading and working heights. Document how any simulated load reflects the airflow effects expected during operation. |
| Gaps in the evidence | Check calibration records and logger time alignment. Locate missing traces, unmeasured bays and periods with no record of conditions or operating events. | Collect evidence aimed at the unresolved location or condition. Until then, limit the conclusion to the area and operations the records support. |
Translate the worksheet into a decision by zone. A warehouse may have an interior room with strong evidence and a dock-adjacent area where a second campaign is warranted. Keep the outcome tied to the places where stock will actually be held. If the two zones share air or freight moves through both, document that interface when assessing whether the evidence from either zone covers the intended use. EU GDP § 3.2.1, WHO temperature-mapping supplement
Retain one campaign. Document the combination of original mapping and additional evidence that covers the current layout, anticipated loads and credible thermal extremes. Identify the positions to which the conclusion applies and the events that would reopen it.
Repeat under seasonal conditions. Specify which outside conditions, control modes and operating patterns the follow-up should capture. Where both cold and warm conditions could materially affect the space, justify how the evidence will address each. Retain comparable positions across studies and explain any changes in load or layout that could affect the comparison.
Collect more evidence. Name the gap and the record or targeted measurements that could close it. Assign an owner and a decision date before committing space that depends on the result. Keep unresolved exposure visible in the plan for peak inventory.
Set logger positions and study duration around the question the follow-up must answer. For example, a study that spans quiet storage but misses the busiest loading periods may still leave dock exposure unresolved. A logger plan for high racks should reflect the highest height occupied by stock and the aisles affected by the air path. The US warehousing section and EU storage-area text do not supply a universal logger count or study duration. Use the technical guidance and justify these choices in the protocol for the particular site. 21 CFR 211.142, EU GDP § 3.2.1, MHRA Inspectorate commentary, WHO temperature-mapping supplement
Apply the worksheet to the April study
Start with two separate questions. Did the April map cover the planned load and storage heights? Did April produce the thermal and operational conditions that could stress those locations in July and August? The first calls for a comparison of layouts and airflow paths. The second calls for weather and operational evidence. A report that calls the April result acceptable for its study conditions can be sound while leaving both of those questions open.
Suppose the April loggers were placed at floor and middle rack levels, and the peak plan puts full pallets on the top racks near a sun-exposed wall and an active dock. That change introduces occupied airspace and patterns of door use that the study may not have captured. Define the planned loading, measure the exposed positions during representative warm operations and compare them with reference positions toward the interior. Confirm whether cold-season exposure at the dock also matters for year-round use. If heat and pallet density change together between campaigns, record both so the team can judge what the comparison actually shows. MHRA Inspectorate commentary, WHO Supplement 8 §§ 2.2.4–2.2.6
For an interior room, the same April date can lead to a different outcome. There may be a case for using the existing campaign if it covered the storage positions at representative load and corroborating records span the relevant outdoor conditions and HVAC modes. Facility history should include where it was measured. A clean summer trace from a single interior probe helps establish what happened there. If the original map omitted the upper rack or the room’s airflow changed when pallets were added, use targeted measurements to resolve those exposures. For the July and August commitment, record which zones and operating conditions QA has evidence to rely on and which need further work. EU GDP § 3.2.1, MHRA Inspectorate commentary, WHO temperature-mapping supplement
Use the results to place probes and define review triggers
Compare the warmest and coldest occupied locations, the positions with the widest fluctuations and the recurring peaks or dips associated with operations. Resolve out-of-range readings through the site’s deviation process. An overall average can be useful for comparing locations, but a local excursion can disappear into it. For each permanent monitoring point, record the study position, height and condition it represents, and check whether the current probe layout covers the important extremes across the conditions studied. If the extremes move between seasons, make sure the monitoring plan can detect the exposure at the positions that matter in each season. EU GDP § 3.2.1, MHRA Inspectorate commentary, WHO Supplement 8 §§ 2.4.1–2.4.4
Keep the conclusion with the annotated position plan, calibration evidence, trace files, load description and relevant activity or weather records. Summarize which storage limits and operations the conclusion covers and explain why the evidence supports each decision. For outsourced storage, identify who supplies the underlying evidence and who reviews the impact on the proposed inventory. The EU guidelines address the respective duties of the parties in their section on outsourced activities. EU GDP chapter 7, WHO temperature-mapping supplement
Reopen the assessment if the building envelope, temperature-control equipment, setpoints, racking or dock flow changes in a way that could alter exposure. Repeated excursions or a new product with different storage limits can also expose an assumption that needs checking. EU GDP § 3.2.1 specifically calls for repeat mapping after significant facility or temperature-control equipment modifications. For other changes, record the impact assessment, evidence reviewed and rationale for the scope of any follow-up. Make the decision available before reserving new zones or heights for peak stock. EU GDP § 3.2.1, MHRA Inspectorate commentary
Sources
21 CFR 211.142 - Warehousing procedures (Title 21, Part 211, Subpart H). Electronic Code of Federal Regulations. Accessed November 18, 2026.
Guidelines of 5 November 2013 on Good Distribution Practice of medicinal products for human use (2013/C 343/01). European Commission, Official Journal of the European Union. Accessed November 18, 2026.
Temperature mapping - an introduction (MHRA Inspectorate blog, 14 July 2016). Medicines and Healthcare products Regulatory Agency. Accessed November 18, 2026.
Temperature mapping of storage areas - technical supplement to the WHO model guidance for the storage and transport of time- and temperature-sensitive pharmaceutical products (TRS 961, Annex 9). World Health Organization. Accessed November 18, 2026.




